The gates come with a spring loaded sliding bolt assembly and 2 gate eyes. The gates have 3 holes for gate eyes, the distance from the base of the end post to the base of each hole is as follows - 12cm, 100cm, 105.5cm. (Two are used). The base of hole for the spring bolt is 72.5cm from the base of the gate.

Damage to centre section of rail second from top

The gates come with a spring loaded sliding bolt assembly and 2 gate eyes. The gates have 3 holes for gate eyes, the distance from the base of the end post to the base of each hole is as follows - 12cm, 100cm, 105.5cm. (Two are used). The base of hole for the spring bolt is 72.5cm from the base of the gate.

1.143m high full mesh 4 bar. The gates come with a spring loaded sliding bolt assembly and 2 gate eyes. The gates have 2 holes for gate eyes, the distance from the base of the end post to the base of the hole is respectively 12cm and 100.05cm. The base of hole for the spring bolt is 56cm from the base of the gate.

Sizes shown are in stock. The gates come with a spring loaded sliding bolt assembly and 2 gate eyes. The gates have 2 holes for gate eyes, the distance from the base of the end post to the base of each hole is respectively 14cm and 170cm. The base of hole for the spring bolt is 92cm from the base of the gate.

The galvanised sheep hurdles are particularly useful during lambing or for sheep handling. Portable, strong and lightweight, loop ends which slot together

These 4.5inch diameter gate posts will take the weight of a 15ft gate if necessary. The slots are 152cm from base of post to base of slot. The lots are 10cm long. Standard post has one slot, dual post has two slots, ground socket is the metal socket designed to be set into the ground to hold a post so that it can be removed later if necesary.

Standard post has one pair of hooks 0.884m apart. Base ofr post to base of hooks - distances respectively 96.5cm and 184.5cm. Dual post has two sets of hooks set that distance apart. Inverted post has a single set of hooks with the top one of the pair inverted so that the gate cannot be lifted off it's hinges.Base of hooks 96cm and 189cm from base of post. Ground socket - the metal socket intended to be set into the ground to hold a post so that it may be lifted in and out

Post to hang suitable for deer gates only. Galvanised 114.3mm diameter. Single set of hooks Base of pst to base of each hook - distances respectively 85.5cm and 246.2cm

Galv metal post to slam to suit deer gates. Single slam slot base of which is 162.5cm from base of post, slot is 10cm long.

This galvanised gate hook has a 19mm diameter pin and it is suitable for most metal gates and the larger sizes of wooden gates. The angle of the hook through the gate post can be adjusted using the back screw to lift a sagging gate slightly. 34cm long, pin height 6.5cm. Screw shank 17cm long

This galvanised gate hook has a 19mm diameter pin and is used as a bottom hook for hanging gates, it is weight bearing. Overall length 22cm, pin height 6cm

19mm dia gate crook - screw in. Overall length 23cm, pin height 7.3cm

This galvanised hook has a 19mm diameter pin and is used set in concrete in walls.

Pair of rectangualr 19mm galvanised gate hangers

This galvanised 19mm hook has 4 screw holes in the plate so that it can be screwed onto walls or posts. Single plate only

This 13mm diameter galvanised hook is mostly used as an adjustable top hook for smaller wooden gates.

This 13mm diameter galvanised hook is used as a bottom hook for smaller wooden gates.

These are ungalvanised to fit them for welding

These are ungalvanised to fit them for welding

These are ungalvanised to fit them for welding

These are all suited to 19mm hooks, the size given is the length of shaft. To fit 7 bar, mesh, deer mesh or half mesh gates

Large stand off auto gate catch galvanised

the archetypal farm gate closure.

this is used for metal gate pairs and it is necessary to drill a hole in the gate frame in order to fit it, ideally it should be used with a drop bolt. Health and Safety note, this design has been criticised because it can drop on a hand or arm.

this sliding gate frame joins two gates and cannot fall on anyones hand or arm (although it could slide into them),it is regarded as safer. It is also much heavier and puts considerable strain on the gate hinges.

Heavy Hasp and Staple

This drop bolt is used to stabilise a closed pair of gates or to hold a gate in a particular position, although strong it will not hold for more than a few years on it's own in a windy situation.

This drop bolt is used to stabilise a closed pair of gates or to hold a gate in a particular position.